Categories
Product Catalog
  • MB-22 - EZ Marble and Terrazzo Polish, 10lbs

MB-22 is a unique combination of specialty abrasives and catalysts that makes the art of Marble and Terrazzo polishing relatively easy to implement without the need of any power tools. MB-22 Marble and Terrazzo polishing powder is designed for spot polishing of most water stains or rings from polished marble, travertine and any other calcite-based stone.

Be certain to test product on a Seprate tile or inconspicuous area first before use as a precautionary measure.

This is perfect for the Do It Yourselfer or small projects at home. All you need to do is add some water and hand buff it with a terry cloth until your stone is back to it's original gloss.

 

DIRECTIONS FOR THE USE OF MB-22 E-Z MARBLE AND TERRAZZO POLISH

The following directions are an average recommendation. Different stones may require different quantities of product along with various techniques. If you are in doubt, don’t hesitate to call us.

Countertops- Always make sure proper masking of the work area is utilized to protect surfaces from messy splatters product.

Wear safety glasses and gloves.

  1. Make sure the surface is free of any coatings, waxes, sealers grease and or soil.
  2. If the surface requires honing use quality diamonds and hone surface correctly predicated upon the clarity of the stone being worked on.
  3. Using your favorite right angle grinder with a 4, 5 or 7 inch pad driver use a hogs hair pad or a quality white polishing pad.
  4. Use about a 1/3 oz per 2-3 square feet(remember the amounts will vary) of product and use enough water to create a wet paste but thick enough not to make a splattering mess.
  5. Start by targeting a 2-3 sq. ft. area and place the product and water in the center of your target. Place your machine and hogs hair or white pad directly on top of it. Starting slowly spread the product out over the area. The use of pressure will vary depending on the stone but generally you can apply an even light pressure. Run the machine on a slow setting for about a minute per sq ft.
  6. Check the results and repeat if needed(Get the pad loaded). When you are satisfied of the results move on to the next area. Working with this polish you will find that you can get good results close to edges,sinks faucets,tub surrounds and tight spaces. A white pad cut ½ inch over the diameter of the pad driver protects the fixtures or surface you are polishing against.

FLOORS - - Always make sure proper masking of the work area is utilized to protect surfaces that could be splattered by product.

Wear safety glasses and gloves.

  1. Make sure the surface is free of any coatings, waxes, sealers grease and or soil.
  2. If the surface requires honing use quality diamonds and hone surface correctly predicated upon the clarity of the stone being worked on.
  3. Target an area of approximately10-12 sq. ft. and place in the center two(2) ounces of product which you will place your machine with a hogs hair pad on top of.Then drop approximately five(5) seconds of water to wet the product so that you get a semi-thick slurry but one that won’t splatter about.
  4. Run your floor buffer over the area for approximately 3-4 minutes per 10 to 12 sq feet. After three minutes check the results if good your are ready to move to next area.If you want more luster run for another minute. When ready move to next area pulling slurry with you with a squeegee and reset the timer.Then begin buffing adding some powder and water as needed to make slurry a semi thick consistency and run for the prescribed time.
  5. Repeat this process three times for a total of 30-36 sq ft and then vaccum up all the slurry and mop the area clean. Start again from number instruction number 3. No need to protect the splatters from etching so just keep going and have no worries.

Write a review

Please login or register to review

MB-22 - EZ Marble and Terrazzo Polish, 10lbs

  • $152.00


Tags: MB-22 - EZ Marble and Terrazzo Polish, 10lbs